CLKTMEAVGMAXTRPODOMHThis manual explains the instal-lation and use of the Trek Incite 6i and Incit
8The computer wire is usually longer than needed. Extra wire length can be diverted by wrapping it around the brake housing
9The magnet must pass across the line on the sensor (Figure 9).1. Align the sensor with the magnet.2. Orient
05. Tighten the nylon ties and trim the excess length (Figure 10).InstallationFigure 0- Trim excess nylon tie length
You can program the starting values of your computer in a single, easy procedure:• Units• Clock• Wheelsize• Odometer The Units set
2Easy setup (ReSet)CLKTMEAVGMAXTRPODOMHFigure - Buttons on the Incite 6i computerModeSetWhen setting the computer, there are three
3CLKTMEAVGMAXTRPODOMHModeSet1. Cycle Mode to ODO (Figure 12).2. Hold Set•KMH or MH flashes.3. Cycle ModeMH and KMH interchange on
4CLKTMEAVGMAXTRPODOMHModeSetNote: If you want to set a custom wheel size, go to page 24 now.3. Cycle ModeThe Wheel Size changes.4. Hold Set• to selec
5CLKTMEAVGMAXTRPODOMHModeSet5. Cycle ModeThe wheel size changes.6. Hold Set• to select.The computer returns to current speed.To set the second wheel
CLKTMEAVGMAXTRPODOMHModeSet1. Cycle Mode to CLK (Figure 14).2. Hold Set•“12” or “24” flashes.Easy setup (ReSet)CLKFigure 4- CLOCK screen
CLKTMEAVGMAXTRPODOMHModeSetYour computer stores data for two intervals- since last ReSet and since last ReStart. ReSet
iiSafety and general guidelines ...1Functions ...
8CLKTMEAVGMAXTRPODOMHModeSetOnce the computer is programmed and installed, it is very easy to use. To change to di
9The Incite 6i computer is designed to be easy to install and maintain. However, computers occasionally have problems. Table 3 shows s
20If the computer is giving erratic information, the computer or hear rate strap battery may be running low on power (normally ac
2Replacing the Battery4. Lift the battery cover, exposing the battery.Be careful to avoid losing the rubber O-ring seal.5. Remove the old battery.It
22CLKTMEAVGMAXTRPODOMHModeSetThe procedure is almost the same as the basic setup on pages 13-14, except instead of picking a
23CLKTMEAVGMAXTRPODOMHModeSet3. Cycle Mode through the wheel sizes to the 4-digit number4. Push Set•The left-hand digit flashes.5. Cycle ModeThe right
24 Setting Custom Wheel SizeFigure 8- Measuring rollout for wheel sizeTable 1 approximates the circumfer-ence of eac
25Limited WarrantyTrek Bicycle Corporation warrants each new Incite computer against defects in workmanship and materials.
While riding your bicycle, do not stare at the computer for long periods of time (Figure 1). If you do not watch the roa
2Table - Function abbreviations, names, and explanations CLOCKCLKTMETime of day Displays in hours and minutes, or stopwatch
3SPEED Always displaysCurrent speed of the bicycle in miles per hour (MH) or kilometers per hour (KMH) AVG- (8i only) Average speed since
4Tools needed:• Electrical tape• Slot-type screwdriver• Phillips-type screwdriver• ScissorsInstallationStem mountHandlebar mountSpeed sens
5The Trek Incite 6i and 8i computer can be mounted on the handlebar or on the stem (Figure 3).
6 InstallationCheck that the computer base cannot be rotated around the handlebar, and that the computer cannot slide backwards on the computer base (
The wheel magnet must be aligned so that it passes across the sensor. As the magnet passes the sensor, it must be no further from t
Commentaires sur ces manuels